Audible shallīe defined to be in compliance with ISO 7779 (DINĮN27779:1991) Noise measurements of machinesĪcoustics. The power supply shall not produce audible noise Visible screen artifacts, when 1/2 cycle of AC power is Shall be able to function properly, without reset or Shall be able to withstand 1.5 times nominal line
Shall be compatible with all PC type computers, ISO13406-2 & MPRII), TUV-S, NOM, GOST-R, HYGIENIC (20 copies), ENERGY, Energy Star,ĬCC, BSMI, PSB, C-TICK, KTL/MIC, SASO, WEEE, RoHSĮqual to twice the weight of the monitor for five Keep wires in their original position so as to reduce interference.Īdjustment of this product please refers to the user' manual. Keep wires away from high voltage, high temperature components and sharp edges. When replacing parts or circuit boards, clamp the lead wires around terminals before soldering. Replacement parts, which do not have the same safety characteristics as specified in the parts list, may create shock,
Before replacing any of these components read the parts list in this manual carefully. Many electrical and mechanical parts in this chassis have special safety visual inspections and the protectionĪfforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage,Įtc. Apply non-ammonia basedĬleaner onto the cloth, not directly onto the glass screen.ĭo not place heavy objects on the monitor or power cord.
Clean the cabinet with a clean, dry cloth. If it gets wet, unplug the power cable immediately and consultĪlways unplug the monitor before cleaning it. Put your monitor only in a lean, cool, dry environment. Stop using the monitor if the cabinet is damaged. There are high-voltage parts inside that may cause electric shock to human Only the qualified technician canĭo not remove the monitor cabinet. Use only the special power adapter that comes with this monitor for power input.ĭo not try to repair the monitor by yourself, as it contains no user-serviceable parts. You're unsure of the power supply in you residence, consult your local dealer or Power Company. This monitor should be operated only at the correct power sources indicated on the label on the rear of the monitor. Used or installation may cause damage to the monitor as well as to the user. This monitor is manufactured and tested on a ground principle that a user's safety comes first. ViewSonic is a registered trademark of ViewSonic Corporation.Īll other trademarks used within this document are the property of their respective owners. Optiquest is a registered trademark of ViewSonic Corporation. Further, ViewSonic reserves the right to revise this publication and to makeĬhanges from time to time in the contents hereof without obligation of ViewSonic to notify any The contents hereof and specifically disclaims any warranty of merchantability or fitness for any ViewSonic makes no representations or warranties, either expressed or implied, with respect to
Optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Language or computer language, in any form or by any means, electronic, mechanical, magnetic, May be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583Ĭopyright (C) 2006 by ViewSonic Corporation. górną podepnę dolną podświetla dolna i tak na zmianę jednakże dwie nie chcą prawidłowo działać.Ĭzy w związku z tym monitor może się uszkodzić ? W sumie przy jednej świetlówce matryca podświetlona jest wystarczająco.Pytanie co może powodować taką usterkę ? Dodam, że pojedyńczo świetlówki świecą niezależnie do którego gniazda je wepnę. Monitor ruszył po wymianie stabilizatorów 3,3V oraz 1,8V, podświetlanie po 1 sek zgasło, profilaktycznie wymieniłem bo miałem 2xAP 9971 bez efektu, uszkodzona była świetlówka(wymieniłem ) i teraz tak.Monitor podświetla jedna świetlówka, jak wepnę drugą podświetlanie wyłącza się natychmiast, odpinam np.